D-RINGS & MAXITAPE
WHEN TO USE D-RINGS & MAXITAPE
- For tools weighing up to 2.3kg or 0.9kg depending on the D-Ring.
- When a non-conductive attachment point is needed for tools up to 0.9kg.
- When Quick Rings, Quick Spins and D-Ring Cord Attachments won’t work. Many tools do not have pre-drilled holes for
- Quick Rings, and lack handles that a Quick Spin will fit.
- When a tool is over 2.3kg or 0.9kg depending on the D-Ring.
- When a D-Ring will interfere with the safe working condition of the tool.
HEAT SHRINKS
WHEN TO USE HEAT SHRINK
- Used on top of MaxiTape to create a more abrasive resistant attachment point.
- When a tool is over 2.3kg or 0.9kg depending on the D-Ring.
- When a D-Ring will interfere with the safe working condition of the tool.
D-RING CORD
WHEN TO USE A D-RING CORD
- For tools weighing up to 2.3kg.For creating quick attachment points on a variety of tools.
- On tools with closed handles, or with pre-drilled holes.
- When a tool is over 2.3kg or 0.9kg depending on the D-Ring.
- When a D-Ring will interfere with the safe working condition of the tool.
QUICK RINGS
WHEN TO USE A QUICK RING
WHEN NOT TO USE A QUICK RING
- When there are pre-drilled holes in a tool, or when a quick ring can be fitted around a tool in such a way where it cannot slide off. Never modify a tool in a way that would void the manufacturers warranty.
- When a tool weighs less than 0.9kg.
WHEN NOT TO USE A QUICK RING
- When a tool is over 2.3kg or 0.9kg depending on the D-Ring.
- When a D-Ring will interfere with the safe working condition of the tool.
TOOL SHACKLES
- Stainless steel material is corrosion resistant.
- One step retrofit attachment for temporary or permanent connection point.
- Secure by tightening with wrench or pliers or add a drop of adhesive.
- Maximum working capacity up to 6.8kg depending on model and lanyard used.
TOOL CINCH ATTACHMENTS
WHEN TO USE A TOOL CINCH
WHEN NOT TO USE A TOOL CINCH
- Tools weighing up to 15.9kg unless otherwise stated.
- On difficult to tether tools such as pinch bars, torque wrenches, clamps and many closed handled tools.
WHEN NOT TO USE A TOOL CINCH
- Do not use a Tool Cinch on tools over 15.9kg .
- When a Tool Cinch will interfere with the safe working condition of the tool.
LANYARDS
- A variety of lanyards suitable for virtually any tool.
- Third-party load rated and developed exclusively for tool drop prevention.
- Maximum working capacity up to 4.6kg depending on lanyard used.
LANYARD BUCKLES
- Modular quick connecting buckle for exchanging multiple tool.
- Stretch cord surrounded by tubular nylon webbing.
- Adjustable barrel lock for tool attachment. Maximum safe working capacity of up to 2.26kg.
TRIGGER TO TRIGGER LANYARDS
- Used in combination with D-Rings and Quick Rings Trigger to Trigger Tool Lanyards are an economical tethering solutions for most hand tools.
- Pull down on the trigger to open the dual-hooked connector, then release once latched to a tool.
- Maximum safe working capacity of up to 4.5kg.
HARD HAT LANYARD
- Comfortably attaches to hard hats and other headwear.
- Double lock plastic buckle attaches to fall protection.
- Made from comfortable high stretch hi-vis lime coloured elastic material.
- Maximum safe working capacity of up to 0.9kg and third party tested using 2:1 safety factor.
BELT LOOPS
- Maximum safe working capacity of up to 2.3kg.